I think if you do this then it will solved your problem.You may also benefited from following posts............
Network Solution For RDA 6231
For All Latest Android Phone Firmware;China , Nokia Software, Hardware And Other Better Solution
Wednesday, July 16, 2014
China Network 100% Working Solution For RDA 6645
Sometimes we face as problem that after replacing pa(RDA 6645)
the network doesn't ok or Show Emergency only though there there is
full signal appear.I have faced this problem for mane time and then I
solved this problem by following way.The way is;after replacing pa
(RDA6645) also replace two red marked capacitor shown on picture.
China PA RDA 6635 Network Solution 100% Working
Sometimes we face as problem that after replacing pa(RDA 6635)
the network doesn't ok or Show Emergency only though there there is
full signal appear.I have faced this problem for mane time and then I
solved this problem by following way.The way is;after replacing pa
(RDA6635) also replace two red marked capacitor shown on picture.
I think if you do this then it will solved your problem.You may also benefited from following posts............
Network Solution For RDA 6231
China Earphone logo Removing Solution 100% Working (6500 Port)
For china earphone logo removing solution (6500 Port) just make a
jumper from Battery (+) to Earphone plug in pin
of Earphone/Charging connector as like as the picture shown bellow.If
there is on any other problem;it will work 100% granted.For N95 port Earphone Logo Solution see this post and for V2 port earphone solution show this post For V3 earphone logo solution show this post
Note:Earphone/Headphone plug in pin may be different for different mobile.Such as,For Symphony B10i it is pin no.2 from left side of headphone/charging connector;For octenn T11 it is pin no.5 from right side of earphone/headphone connector.So to solve this problem you have to check every pin of headphone connector one by one.Remember that during checking time you have to power on your phone through DC Power Supply instant off Battery.If you power on your phone with battery during this time ,your may be damaged.So be careful about this.
Proved Solution:
Note:Earphone/Headphone plug in pin may be different for different mobile.Such as,For Symphony B10i it is pin no.2 from left side of headphone/charging connector;For octenn T11 it is pin no.5 from right side of earphone/headphone connector.So to solve this problem you have to check every pin of headphone connector one by one.Remember that during checking time you have to power on your phone through DC Power Supply instant off Battery.If you power on your phone with battery during this time ,your may be damaged.So be careful about this.
Proved Solution:
Symphony Ft03 Mic Solution 100% Tested
For Symphony Ft03 Mic solution Just make those jumper shown in picture bellow.It is 100% tested.
Symphony B10i Earphone logo removinr solution 100% working
For china earphone logo removing solution of Symphony B10i just make a
jumper from Battery (+) to Earphone plug in pin (Pin no.2 of Symphony B10i)
of Earphone/Charging connector as like as the picture shown bellow.If
there is on any other problem;it will work 100% granted.For N95 port Earphone Logo Solution see this post and for V2 port earphone solution show this post
For V3 earphone logo solution show this post
Note:Earphone/Headphone plug in pin may be different for different mobile.Such as,For Symphony B10i it is pin no.2 from left side of headphone/charging connector;For octenn T11 it is pin no.5 from right side of earphone/headphone connector.So to solve this problem you have to check every pin of headphone connector one by one.Remember that during checking time you have to power on your phone through DC Power Supply instant off Battery.If you power on your phone with battery during this time ,your may be damaged.So be careful about this.
For V3 earphone logo solution show this post
Note:Earphone/Headphone plug in pin may be different for different mobile.Such as,For Symphony B10i it is pin no.2 from left side of headphone/charging connector;For octenn T11 it is pin no.5 from right side of earphone/headphone connector.So to solve this problem you have to check every pin of headphone connector one by one.Remember that during checking time you have to power on your phone through DC Power Supply instant off Battery.If you power on your phone with battery during this time ,your may be damaged.So be careful about this.
China Earphone Logo 100% working Solution (V3port)
For china earphone logo removing solution for V3port just make a
jumper from Battery (+) to Earphone plug in pin (Pin no.2 of Symphony B10i)
of Earphone/Charging connector as like as the picture shown bellow.If
there is on any other problem;it will work 100% granted.For N95 port Earphone Logo Solution see this post and for V2 port earphone logo solution show this post For 6500 Port earphone logo Solution see this post
Note:Earphone/Headphone plug in pin may be different for different mobile.Such as,For Symphony B10i it is pin no.2 from left side of headphone/charging connector;For octenn T11 it is pin no.5 from right side of earphone/headphone connector.So to solve this problem you have to check every pin of headphone connector one by one.Remember that during checking time you have to power on your phone through DC Power Supply instant off Battery.If you power on your phone with battery during this time ,your may be damaged.So be careful about this.
Proved solution for Symphony B10i
Note:Earphone/Headphone plug in pin may be different for different mobile.Such as,For Symphony B10i it is pin no.2 from left side of headphone/charging connector;For octenn T11 it is pin no.5 from right side of earphone/headphone connector.So to solve this problem you have to check every pin of headphone connector one by one.Remember that during checking time you have to power on your phone through DC Power Supply instant off Battery.If you power on your phone with battery during this time ,your may be damaged.So be careful about this.
Proved solution for Symphony B10i
Subscribe to:
Posts (Atom)